100% Original 2017 TEVO Black Widow 3D Printer DIY KIT
KIT INCLUDES COMPLIMENTARY 8GB SD MEMORY CARD
MASSIVE 370x250x300 PRINT/BUILD AREA!!!
“NEW 2017 STOCK WITH UPGRADED MKS Gen V1.4 BOARD, UPGRADED HEATED BED AND INCLUDED EXTERNAL SSR”
2019 Black Widow 3D Printer info:
Like it’s little brother (The Tarantula) The Black Widow is based on the Prusa i3, a proven design with tens of thousands of users all around the world. Unlike it’s little bro however the Black Widow is much larger with a MASSIVE print area and built with a much stronger frame to reduce flex when printing!
You now have a unique opportunity to own your very own 2017 Black Widow 3D Printer.
All parts of this printer are Open Source and are part of the RepRap project. In the event you may require parts these are all readily available.
The Black Widow 3D Printer consists of all metal parts in its frame construction – extruded black anodised aluminium is used for the frame material with aluminium end plates for the assemblies and ball bearing V-groove wheels for silky smooth, quite operation. There are no smooth rod, linear bearing issues you find with other printers within this price range!
The MASSIVE aluminium print bed plate is 370mm in size on the X-Axis and 250mm on the Y-Axis. The entire bed is heated by a 24-Volt power supply. This allows for much faster warm-up as well as a consistent temperature due to lower response times.
The X-Axis travel is around 380mm (side to side) for the extruder carrier (some reduction due to hot-end physical size limitations). The X-Axis plate rides on silky smooth German-made ball bearings on the X-Axis track. The Y-Axis travel has 250mm of usable distance to work with. The Y-Axis bed support plate rides on silky smooth German-made ball bearings on the Y-Axis track. The Z-axis is limited by the physical dimensions of the frame – there is around 300mm of usable distance to work with on the Z-Axis.
Distance may vary slightly depending on your assembly techniques. Both sides of the X-Axis track are lifted by a lead screw at each end. The lead screws are synchronised together using pulley gears on the screws and a pulley gear on the Z-Axis stepper motor above the frame. The Z-Axis stepper motor and the two lead screws are linked using an endless loop GT-2 belt which keeps the two lead screws turning at the same time. There are no ‘lead screw’ motor slippages as can be experienced by twin Z-Axis motor configurations as the belt does not allow the lead screws to get out of sync.
The power supply is now installed inside a power unit enclosure along with the main board and LCD panel display for local control of the printer. Installation of the power supply removes the issue of possible electrical shocks due to exposed mains power connections. The power unit enclosure has a SD Card slot to allow printing locally without connecting to a computer. Simply load a G-code file on the SD Card then select the file using the LCD panel and print.
The Hot-End of the printer is a new design which makes changing the nozzle assembly a breeze. The entirely metal nozzle/heat break assembly is held in the hot-end assembly by a clamp screw. The heat radiator on the heat break tube is screwed onto the tube for much better thermal conduction. Removal and replacement of the nozzle/heat break is simple. Simply loosen the retaining clamp screw, unscrew and remove the radiator from the heat break tube then slide the nozzle assembly out of the bottom of the hot-end mount. To put it back together is just as simple. To align the nozzle simply place a piece of paper under the nozzle, loosen the clamp screw to allow the nozzle to contact the paper and then tighten the clamp screw.
The filament feed motor assembly now uses a 5:1 reduction gear transmission to increase the torque force exerted on the filament during printing – no more “CLICK-CLICK-CLICK” of the feeder due to either partially blocked hot-end assembly or not enough force to feed the filament at the right flow-rate during printing. The entire hot-end/feeder assembly is made from metal so there is no concern for warpage due to high temperatures during long printing sessions.
The OPTIONAL upgraded Black Widow BL Touch version uses Proximity sensors on all three Axis of movement along with modified firmware. This reduces the possibility of sensor damage as there are no moving parts to snag or break during assembly or operation. Using proximity sensors allows for much finer control of the positional trip point detected with high accuracy and repeatability.
This is a DIY KIT (Unassembled). All you need is included in the kit (even a complimentary 8GB SD memory card) so you can get started straight away!
The buyer is wholly responsible for the assembly and as such Click Depot will not accept any returns for this kit once unpackaged and/or assembled.
Whilst the Black Widow is relatively simple to assemble and set-up it does take time and patience. It is also important that you have a basic understanding of mechanical assembly techniques and electrical wiring.
Under no circumstances should you handle wiring or the power supply when this machine is plugged in and/or turned on. One should maintain a healthy respect for electricity at all times.
To avoid burns do not touch the heated print bed when operating and in particular the hot-end.
For younger users, (below 18yrs) we would strongly recommend an adult be present to supervise during assembly/set-up and also during operation.
The input mains adaptor on the power supply is selectable between 110V – 220V.
Black Widow 3D Printer Specs:
Name: 2017 Black Widow PrinterModel: Black Widow – Prusa i3
Positioning Accuracy: Z 0.004mm, X & Y 0.012mm
Minimum Layer Thickness: 50 MicronsLayer Resolution: 0.05mm
MAX Printing Speed: 100mm/sRecommended Printing Speed: 70mm/s
Build Size: 370x250x300mmPrinting Colour: Single Colour/Single Head
Filament Types: PLA, ABS, Nylon, PETG, Wood PVA and Flex
Extruder Type: Spider Teeth 5:1 Ratio Feed Extruder
Extruder Diameter: 0.4mm
Filament Diameter: 1.75mm
Recommended Extruder Temperature: 210°C (The maximum can be set to 260°C)
Heating Plate Temperature: 60-120°C (When in a 25°C environment with no drafts)
Best Ambient Temperature: ≥25°CPower Requirements: 220V, 500W, 50/60Hz, (110-V switchable) 24V Output
Control Electronics: MKS Gen V1.4
Connection: SD card on LCD Display or USB
File Print Format: STL, G-Code (SD-Card G-Code only)
Compatibility: Windows XP, Windows 7, Windows 10, Linux, Mac OSXCE, FCC
Specs: CE, FC, ROHS
Device Weight: 16kg
Equipment Size: 650x510x520mmPackage Size: 630x430x250mm
Shipping Weight: 18.5kg
Material Colours: White, Green, Red, Blue, Yellow, Black, Transparent, Orange, Grey and more
Expedited Shipping is on us!!
Free Expedited Shipping?!?!
Provided there are no unforeseen delays your 3D printer should get to you within 2-10 business days from date of order!!
Please note: Shipping may take longer than that general 2-10 business days if you are located outside of a metropolitan area.
Free Expedited Shipping is available to the following countries:
Australia, New Zealand.
International Shipping Info:
Should stock be shipped from our overseas warehouse we generally ship with partner couriers DHL, FedEx, UPS, TNT and EMS.
Goods generally ship same day and take approximately 5-10 business days to be delivered to destination.
Local Shipping Info:
For local stocks/shipments we usually ship with Auspost, CouriersPlease, PackSend, Allied Express and StarTrack. Shipping usually takes 2-6 business days.
We specifically choose the services of reputable couriers. This is so we minimise potential delays, losses and damages. These services also allow us to track items in real time.
These services naturally do come at a higher cost. This however is how we have chosen to best manage our shipping from point A to point B. Your customer satisfaction is our first and foremost priority!
To avoid any unnecessary delays please ensure your contact info (Address/Phone number) is accurate. A mobile number is recommended and is required in case the courier needs to contact you.
Once shipped a tracking number will be provided to you. You will then be able to check the status of your order in real time via the courier website using your unique tracking number.
Please advise Click Depot as soon as you have taken delivery of your 3D printer. Our team will send you files, links and resources to assist you in getting set-up correctly and allow you the best possible start.
DON’T DELAY STOCK IS LIMITED!!!